website

MTK

Chip: MT7628DAN 2T2R 2.4G 300M 23.5*23.2mm

Projekt nummer eins.:
Main control chip: MT7628DANSpecifications: 2T2RSpeed: 300MInterface: USB, WAN, LAN, I2S, I2C/PCM, UART, GPIOSize: 23.5*23.2 (L*W)Working voltage: 5VWireless standard: 802.11b/g/nBand width: 2.4GWorking temperature: -20C to +85C
Beschreibung Details des projekts

Main control chip: MT7628DAN

Specifications: 2T2R

Speed: 300M

Interface: USB, WAN, LAN, I2S, I2C/PCM, UART, GPIO

Size: 23.5*23.2mm (L*W)

Working voltage: 5V

Wireless standard: 802.11b/g/n

Band width: 2.4G

Working temperature: -20°C to +85°C

Features

 

■ The module is based on Taiwan’s MTK’s MT7628DAN main chip solution, the main frequency is up to 580MHz, with 64MB DDR2 RAM and 8MB SPI FLASH;

■ Conforms to IEEE802.11b/g/n wireless network protocol, supports three working modes of bridging, routing, and access point

■ Adopt 2x2 MIMO (Multiple input multiple output) architecture, wireless signal multi-channel transmission and reception, transmission rate up to 300Mbps

■ Achieve a variety of communication transmission, input and output control, intelligent control of IOT applications, convenient for debugging and product development

■ Multiple GPIOs, 1 UART interface, 1WAN, 3LAN/4LAN wired network port “stamp hole” and “pin” dual design external connection method two IPEX sockets, freely configurable antenna type

■ Application areas: smart home, wireless storage, WIFI speakers, network cameras, baby monitoring, routers, repeaters, wireless APs

Module size chart

 
FDGFDGFD

Module pin

 

WEQEQWEQWE212

 

 

SPI_CS0


GPIO#10SPI bus chip select signal 0
REF_CLKO


GPIO#38Reference clock output
PERST_N


GPI0#36PCIe device reset output terminal
WDT_RST_N


GPIO#37Watchdog timeout reset
EPHY_LED4

JTAG_RST_N



GPI0#39PORT4 LED, active low
EPHY_LED3JTAG_CLK

GPI0#40PORT3 LED, active low
EPHY_LED2JTAG_TMS

GPI0#41PORT2 LED, active low
EPHY_LED1JTAG_TDI

GPIO#42PORT1LED, active low
EPHY_LEDOJTAG_TDO

GPIO#43PORTOLED, active low
PORST_N



CPU reset, active low
UART_TXD1

PWM_CHO
 
GPIO#45Serial port 1 data transmission
UART_RXD1

PWM_CH1GPIO#46Serial port 1 data reception
I2S_SDIPCMDRX

GPIO#OI2S data input terminal
I2S_SDOPCMDTX

GPIO#1I2S data output terminal
I2S_WSPCMCLK

GPIO#2I2S channel selection, 0; left; 1; right
I2S_CLKPCMFS

GPI0#3I2S data bit clock
I2C_SCLX


GPIO#4I2C bus clock
I2C_SD


GPI0#5I2C bus data
SPI_CS1


GPI0#6SPI bus chip select signal 1
SPI_CLX


GPI0#7SPI bus clock signal
SPI_MIS0


GPIO#9SPI bus data master in and slave out
SPI_MOSI


GPIO#8SPI bus data master out and slave in and out
GPI00


GPI0#11Universal input and output interface
UART_TXDO


GPI0#12Serial port О data output
UART_RXDO


GPI0#13Serial port О data input
LED_N


GPIO#44WFi LED, active low
MDI_RP_PO



PORTO network signal reception is positive
MDI_RN_PO



PORTO network signal reception is negative
MDI_TP_PO



The PORT0 network signal transmission is positive
MDI_TN_PO



PORTO network signal sending negative
MDR_TP_P1SPIS_CS
PWM_CHOCPI0#14The PORT1 network signal is being sent
MDI_TN_P1SPIS_CLK
PTM_CH1GPI0#15PORT1 network signal sending negative
MDI_TN_P1SPIS_MISO
UART_TXD2GPI0#16Port1 network signal reception is positive
MDI_TN_P1SPIS_MISI
UART_RXD2GPI0#17Port1 network signal reception is negative
MDI_RP_P2
eMMc_D7PTM_CHOGPIO#18Port2 network signal reception is positive
MDI_RN_P2
eMC_D6PWM_CH1GPI0#19Port2 network signal reception is negative
MDI_TP_P2UART_TXD2eMMC_D5PWM_CH2GPI0#20The PORT2 network signal is being sent.
MDI_TN_P2UART_TXD2eMMC_D4PWM_CH3GP10#21PORT2 network signal sending negative
MDI_TP_P3SD_WPeMMC_WP
GP10#22The PORT3 network signal is being sent.
MDI_TN_P3SD_CDeMMC_CD
GPI0#23PORT3 network signal sending negative
MDI_RP_P3SD_D1eMMC_D1
GP10#24Port3 network signal reception is positive
MDI_RN_P3SD_DoeMMC_DO
GP10#25Port3 network signal reception is negative
MDI_RP_P4SD_CLKeMMC_CLK
GP10#26Port4 network signal reception is positive
MDI_RN_P4SD_CMDeMMC_CMD
GP10#28Port4 network signal reception is negative
MDI_TP_P4SD_D3eMMC_D3
GP10#29The PORT4 network signal is being sent.
MDI_TN_P4SD_D2eMMC_D2
GP10#27PORT4 network signal sending negative
USB_DP



USB data is positive
USE_DM



USB data negative

0012.jpg

第一张.jpg

第三张.jpg

客户来访.jpg

展会.jpg

第五张.jpg


Welcome to TROLINK. Please tell me what product you are making? We want to hear from you so we can better meet your expectations

Schick uns deine daten